Litter-Robot 3 Connect Essentials Bundle

The ramp fits in front of the Litter-Robot. Installation is easy: On the step of the Litter-Robot, peel up the black rubber step mat to reveal the mount for the ramp. Set the narrow end of the ramp on the step, so it rests in the recess. Place the step mat in the recess on the top step of the ramp.

The fence fits onto the bottom of the globe entrance. Installation is easy: Hold the fence upright inside the globe. Tilt the bottom of the fence toward you to align the back of the fence with the built-in kickguard on the globe. Keep the wing tabs of the fence inside the globe while rotating it downward. Gently pull forward and push down on the front of the fence to snap it over the lip of the globe. Make sure the fence is level and the three tabs along the outer rim of the fence are secured over the lip.

The Litter-Robot senses when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. Kittens and small cats that weigh less than 2.3 kg may not be heavy enough to trigger the cat sensor. Therefore, kittens and small cats that weigh less than 2.3 kg can use the Litter-Robot, but not in automatic mode. Until they weigh enough, we recommend using your Litter-Robot in "semi-automatic" mode to keep your cat safe and relieve you from litter box scooping. For "semi-automatic" mode, leave the Litter-Robot switched off or unplugged. When you see your cat has used it, wait about 7 minutes for the waste to clump, then turn it on/plug it in. The Litter-Robot will automatically perform a clean cycle (which takes about 2 ½ minutes). Afterward, turn it off/unplug it again. Continue this supervised, semi-automatic mode until your kittens have gained sufficient weight to activate the cat sensor.

No, the Litter-Robot does not have a weight limit. With entryway dimensions of 39.4 cm H x 26 cm W and interior globe dimensions of 38.1 cm-43.18 cm H (depending on litter level) x 50.8 cm W x 50.8 cm D, almost any domestic cat can fit comfortably inside the globe. However, your cat must weigh at least 2.3 kg to trigger the cat sensor.

No, the Litter-Robot will not eliminate all litter box odour. However, because waste is promptly removed and contained in the base, typical litter box odour will be reduced significantly. Additionally, a large carbon filter located in the front of the waste drawer absorbs odours and moisture to discourage mold growth (a major culprit of that telltale litter box smell). This is why the Litter-Robot is a great choice for multiple-cat households. The amount of odour control the Litter-Robot will provide depends on the amount of odour created—by how many cats use it, what type of litter you use, and your cats' diets, among other things. Of course, the more often you empty the waste drawer, the less opportunity there is for odour to escape. It is also worth noting that scented litters are generally not as effective at absorbing odours as a high-quality unscented litter.

Our robots require a 2.4 GHz WiFi signal and IPv4 addressing (5 GHz band and IPv6 are not supported). Our robots are unable to connect to shared networks (apartment complexes, college dorms, etc.).

We offer single sign-on, which means you will be automatically signed into your litter-robot.com account when using the app. Both accounts will synchronize automatically. That being said, if you set up your app account and litter-robot.com account using different email addresses, this single sign-on will not work.

Your Litter-Robot 3 does not have the ability to track your Scoops Saved when it is not connected to the internet.  Therefore, any cycles that may have occurred when your Litter-Robot 3 was not connected to the internet will not be reflected in your Scoops Saved total.  Regardless, we hope that you enjoy watching your Scoops Saved grow and enjoy the convenience your Litter-Robot 3 is bringing to your life!

Download Litter-Robot 3 user manual

Getting started with Litter-Robot 3